Configuring an SRB
Purpose
Section titled “Purpose”Use this guide to configure a Smart Return Bin (SRB): give it its identity and the WiFi networks it should use. Configuration is done from a phone or laptop over the bin’s own setup network. No cables, software or reflashing are needed, and it can be repeated at any time, for example when a site’s WiFi changes or a spare mainframe is installed.
Reusables staff will give you the values for every field on the setup page. The one exception is the Mainframe ID, which you read off the mainframe itself (see Step 4).
What you need
Section titled “What you need”- The key to the SRB’s rear service hatch (usually held by on-site staff)
- A phone, tablet or laptop with WiFi
- The configuration values from Reusables staff:
- Device ID
- Device Credential
- PCB Version (typically
1.4or2.0) - Primary WiFi network name and password, if the bin will use WiFi
- Enterprise identity and username, only if the site network is WPA2-Enterprise
Step 1: Put the bin into setup mode
Section titled “Step 1: Put the bin into setup mode”- Unlock and open the rear service hatch.
- Press and hold the door button inside the hatch for 10 seconds, then release.
- The bin starts broadcasting its own setup WiFi network. The Network indicator light inside the hatch turns white while the bin is in setup mode.
-
A brand-new bin that has never been configured goes into setup mode on its own when powered on. You can skip the button hold.
-
Step 2: Join the bin’s setup network
Section titled “Step 2: Join the bin’s setup network”On your phone or laptop, join the WiFi network that starts with SRB-Setup-:
- A bin that is already configured appears as
SRB-Setup-<device id>, for exampleSRB-Setup-guelph-srb-5 - A brand-new bin appears as
SRB-Setup-followed by four letters/numbers, for exampleSRB-Setup-3F2APassword:usemewisely
If several bins are in setup mode at once, the network name is how you tell them apart.
Step 3: Open the setup page
Section titled “Step 3: Open the setup page”A setup page usually opens on its own once you join. If it doesn’t, open a web browser, go to http://192.168.4.1 and tap Setup.
The top of the page shows what the bin currently holds, so you can see what you are about to change. This is also where you can obtain an SRB’s MAC address if this is all you need.
Step 4: Fill in the form
Section titled “Step 4: Fill in the form”Identity
Section titled “Identity”| Field | What to enter |
|---|---|
| Device ID | As provided by Reusables. Required. If this is left blank, none of the identity fields are saved. |
| Device Credential | As provided by Reusables. |
| PCB Version | As provided by Reusables, for example 1.4. |
| Mainframe ID | Read this off the mainframe. The number is etched on the mainframe, to the right of the PCB case. Enter the number only, for example 123. |
| Switch Type (if present) | Use one of the following values: mechanical reed_1 reed_2 reed_3 reed_4If unknown, skip. |
| Field | What to enter |
|---|---|
| Primary WiFi SSID / Password | The site WiFi network, as provided by Reusables. Leave blank if the bin runs on LTE (cellular). |
| Fallback WiFi SSID / Password | Already filled in. Leave it as it is. It is the recovery network that lets Reusables bring the bin back online without opening it. |
| WPA2-Enterprise Identity / Username | Only for enterprise networks, as provided by Reusables. Leave blank otherwise. |
Step 5: Save
Section titled “Step 5: Save”-
Tap Save at the bottom of the page.
-
The bin reboots and connects with its new settings. The setup network disappears.
-
Close and lock the service hatch.
-
1. 1. The bin is configured once its **Network indicator light** (second from left) shows it is online (green, white or blue).Let Reusables know you are done so they can confirm the bin has checked in.
Good to know
Section titled “Good to know”- Setup mode times out after 15 minutes. If nothing is saved, the bin reboots and carries on with its existing settings. A hatch closed on a bin left in setup mode sorts itself out.
- Factory reset: typing
ERASEin the field at the bottom of the form wipes the bin’s identity and every stored network, then reboots it back into setup mode. Everything else on the form is ignored when you do this, so erase first, then configure the bin fresh once it comes back. Only do this if Reusables asks you to.
Need help?
Section titled “Need help?”Email support@reusables.com with the bin’s location, its SRB # (label above the hatch lock), and what you have tried.